Hire an Expert : 0086-371-86151927

call us

0086-371-86151927

heat treatment of stainless steel

heat treatment of stainless steel

heat treatment of stainless steel Related Products

  • How heat treating and annealing stainless steel impacts

    But heat treating stainless steel can be tricky. Thermal processes improve some qualities at the expense of others. Heat treaters are tasked with developing the right balance. Balance is achieved when heat treating and annealing stainless steel parts is precisely matched to their makeup and intended use. Types of stainless steel

  • Stainless SteelsProperties and Heat Treatment Alloy

    The heat treatment consists of heating the austenitic steels to 870°C to 900°C, and holding there for 2 to 4 hours, followed by rapid cooling in air, oil, or water. The aim of heating to and soaking is to precipitate out all the carbon from austenite as carbides of titanium, niobium, columbium and leave no carbon remaining dissolved in austenite.

  • Some Thoughts on Stainless Steel and Heat Treating

    May 07, 2012 · With proper steel selection and careful heat treating I can fashion a stainless kitchen knife that cuts just as well as a typical high carbon knife with much less maintenance. Stainless Steel Heat TreatWhat’s so special about it? To me the heat treat is the most critical part of the process.

  • Stress relieving heat treatments for austenitic stainless

    Unlike martensitic steels, the austenitic stainless steels are not hardenable by heat treatment as no phase changes occur on heating or cooling. Softening is done by heating in the 1050/ 1120°C range, ideally followed by rapid cooling. This is of course the complete opposite to martensitic steels, where this sort of treatment would harden the steel.

  • What Happens When Metals Undergo Heat Treatment

    Commonly used in steelmaking today, tempering is a heat treatment used to improve hardness and toughness in steel as well as to reduce brittleness. The process

  • Heat Treating 440C Stainless BladeForums

    Mar 25, 2007 · Raise heat to 1950º F and hold for one hour. Air quench at room temperature. Subzero freeze at 200º below 0. TemperingTemper at 400ºF for one hour, two times _____ ATS 34 Stainless Preheat thoroughly at 1400º/1500ºF and hold for 30 minutes. Raise heat to 1950º/1975ºF and hold for one hour. Air quench at room temperature.

  • Stabilization Heat Treatment of Austenitic Stainless Steel

    stainless steel, and then the weldment is thermally stabilized. While this is not a frequent need, under some corrosive circumstances it may be advisable. The post weld thermal stabilization heat treatment would be the same heat treatment as previously discussed.

  • Heat Treatment Process of Austenitic Stainless Steel

    Depending on the chemical composition, the purpose of heat treatment, austenitic stainless steel often used heat treatment methods are solid solution treatment, stabilization annealing, stress removal and sensitization treatment. 1. Solubilization treatment.

  • Heat Treatment of Spring Steels Metallurgy

    In this article we will discuss about the heat treatment of spring steels. Any metal, or alloy which can be hard drawn, or rolled to fairly high strength and retains sufficient ductility to form, may be used for springs, or any alloy which can be heat treated to high strength

  • Heat Treatment of Bolts & Fasteners Purpose of Heat

    The carbide solution treatment of stainless steel fasteners can improve cryogenic or low temperature toughness and is part of the ASTM A320 specification. ASTM A325, ASTM A490 SAE grade 5 and SAE grade 8 fasteners are made of higher carbon plain or alloy steels, which can be hardened through a quenching and tempering process.

  • Stabilization Heat Treatment of Austenitic Stainless Steel

    Thermal stabilization occurs by heating the chemically stabilized stainless steel to a temperature where titanium or columbium carbides form preferentially and chromium carbides do not form. This heat treatment is conducted at approximately at 1625 °F for chemically stabilized stainless steels and the hold time is typically 4 hours.

  • What Happens When Metals Undergo Heat Treatment

    Commonly used in steelmaking today, tempering is a heat treatment used to improve hardness and toughness in steel as well as to reduce brittleness. The process

  • SS420 Grade AISI 420 Stainless Steel Properties, Heat

    Type 420 Stainless Steel Heat Treatment PrecleaningAll workpieces of SS420 and fixtures must be thoroughly cleaned, such as oil, PreheatingThe thermal conductivity of stainless steel is usually lower than that of carbon steel. Atmosphere protectionAustenitizing temperature 1010 °C (1850

  • SS304 Grade AISI 304 Stainless Steel Properties

    The following is the heat treating 304 stainless steel, such as annealing, forging, hardening, stress relieving, etc. Annealing (Solution Annealing) Type 304 stainless steel annealing temperature range is 1010 1065 °C (1040 °C is recommended) and then rapidly cooled.

Our advantage:
· 20 Years of experience in the Steel field
· 500,000 MT production capacity per year.
· 100+ exporting markets covering global main countries and regions.
· 2000+ MT stock per month with different materials and sizes.
· 150+ projects each year, covering oil tank, shipbuilding, oil&gas pipeline, drilling, offshore, energy, construction industries.

Our Steel Products' Certificates:

Package: